Revitalize Your Worn-out Bathtub With Our Expert Bathtub Reglazing Service in Covina, CA. Our Bathtub Reglazing Contractors Restore The Surface And Leave You With A Refreshed Bathtub.
Bathtub reglazing or bathtub resurfacing restores an old or worn bathtub to its original condition. Bathtub reglazing involves cleaning, repairing any chips or cracks, sanding and stripping the old finish, and then applying a new coat of enamel or other coating. The goal of bathtub reglazing is to make the tub look as good as new while saving homeowners the expense of Bathtub Replacing. It should be noted, however, that reglazing is not suitable for all types of bathtubs, especially those made of fiberglass or plastic.
If you want to restore the beauty of your old bathtub, give us a call at Bathroom Remodel CA for professional and reliable bathtub reglazing services.
Bathtub Reglazing Cost in Covina, CA
The cost of bathtub reglazing can vary depending on several factors, including the size of the bathtub, the extent of the damage, and the region in which the work is being done. On average, bathtub reglazing can cost anywhere from $300 to $600, with larger or more Damaged Bathtubs costing more. However, in some cases, the costs can be significantly higher or lower than this range. Additionally, it is important to keep in mind that reglazing is not a permanent solution, and the finish can wear down over time, requiring additional upkeep or eventual replacement. Therefore, it is important to weigh the costs of reglazing against the option of replacing the bathtub entirely, which can be a more expensive and time-consuming process but may provide a longer-lasting solution.
Bathtub Reglazing Process in Covina, CA
The process of bathtub reglazing typically involves the following steps:
Bathtub Preparation: The technician will first clean the bathtub thoroughly and remove any caulking or other seals around the bathtub.
Bathtub Repair: Any chips or cracks in the bathtub will be repaired using a filler material and sanded down to create a smooth surface.
Bathtub Etching: A solution or acid will be applied to the surface of the bathtub to create a rough surface that will allow the new coating to adhere better.
Bathtub Masking: The surrounding area will be covered in plastic to protect it from overspray.
Bathtub Coating: The technician will apply a new coating to the bathtub, typically using a spray gun, to create a smooth and even finish. The coating will be allowed to dry and cure completely before use.
Overall, the process takes a few hours to complete, but the bathtub will need to be left unused for at least 24-48 hours to ensure the coating cures properly. The result is a shiny, smooth, and durable finish that can extend the life of the bathtub by several years.
Bathtub Reglazing Contractors in Covina, CA
There are many contractors that offer bathtub reglazing services. The Bathroom Remodel CA bathtub reglazing contractors specialize in restoring the surface of bathtubs through a process of applying a new surface coating over the existing one.
Bathtub reglazing contractors typically offer a range of Bathroom Renovation services related to restoring the surface of bathtubs. These may include:
- Bathtub reglazing
- Bathtub repair
- Tile and grout restoration
- Custom color matching
- Anti-slip applications
The goal of the Bathroom Remodel CA bathtub reglazing contractors is to restore the appearance and functionality of bathtubs by creating a new, durable surface layer that lasts for many years to come. When choosing a contractor or company for bathtub reglazing services, it is important to research their reputation, read reviews, and ask for references to ensure the quality of their work and the level of their customer service.
Bathtub Reglazing Benefits in Covina, CA
Bathtub reglazing has several benefits, including:
Cost-effective Bathtub Reglazing: Reglazing a bathtub is generally much more cost-effective than replacing it, which can save homeowners a significant amount of money.
Time-efficient: Reglazing a bathtub typically takes only a few hours, compared to several days or even weeks for a full replacement.
Improved Bathtub Appearance: Over time, bathtubs can become discolored or lose their shine. Reglazing restores their appearance, making them look like new again.
Durable: The new surface coating applied during reglazing is usually quite durable and can withstand years of use without chipping or cracking.
Easy to Clean Bathtub: After reglazing, bathtubs are typically easier to clean since the new surface is smooth and uniform, without rough spots or uneven areas.
Eco-friendly Bathtub Reglazing: Reglazing a bathtub is a more environmentally friendly option than replacing it, which can lead to more waste in landfills.
Methods to Use for Bathtub Reglazing in Covina, CA
There are typically two methods used for bathtub reglazing:
Spray-On Bathtub Reglazing Application: This method involves using a spray gun to apply the new surface coating onto the bathtub. The process involves cleaning, sanding, and priming the surface of the tub before applying the coating in a series of thin layers. The spray-on application method is typically faster than the brush-on method, and it can result in a smooth, even finish.
Brush-On Bathtub Reglazing Application: This method involves using a brush or roller to apply the new surface coating onto the bathtub. As with the spray-on application, the process involves cleaning, sanding, and priming the surface of the tub before applying the coating in a series of thin layers. The brush-on method typically takes longer than the spray-on method, but it can be easier to control and achieve a uniform finish.
Both methods typically involve the same preparation steps, and the choice of method depends on the contractor's preference or the specific requirements of the bathtub being reglazed.
Bathtub Reglazing Steps in Covina, CA
The following are the general steps involved in bathtub reglazing:
Bathtub Preparation: The first step is to clean the bathtub thoroughly and remove any dirt, grime, or soap residue. The bathtub may also need to be sanded to roughen the surface and create a better bond between the old and new surface coatings.
Bathtub Masking: The next step is to apply masking tape or protective plastic to areas around the bathtub that are not being reglazed. This helps to prevent any overspray or drips of the surface coating from getting on other surfaces.
Bathtub Priming: Once the preparation steps are complete, a primer is typically applied to the surface of the bathtub. The primer helps the new surface coating adhere to the old surface and can improve the durability of the reglazed bathtub.
Bathtub Surface Coating: After the primer has dried, a new surface coating is applied to the bathtub. This coating may be applied with a spray gun or roller, depending on the contractor's preference. The surface coating is applied in several thin layers and is left to dry between each coating.
Bathtub Buffing: Once the surface coating has been applied, the bathtub is typically buffed to smooth out any imperfections and create an even finish. This step can be done by hand or with a machine, depending on the contractor's preference.
Bathtub Final Inspection: After the bathtub has been reglazed and buffed, a final inspection is usually done to ensure the finish is smooth and uniform. Any necessary touch-ups or repairs are made at this stage.
Residential Bathtub Reglazing Services in Covina, CA
Residential bathtub reglazing services typically involve the following:
Free Bathtub Reglazing Consultation: Bathroom Remodel CA starts by consulting with the homeowner about the condition of the bathtub and their desired outcome. They may inspect the bathtub to determine whether it is a good candidate for reglazing, or whether it would be better to replace it.
Bathtub Preparation: We will clean and prepare the bathtub for the reglazing process. This typically involves removing any dirt, grime, or soap residue, sanding the surface to roughen it, and repairing any chips or cracks in the surface.
Bathtub Masking: We will apply masking tape or protective plastic to areas around the bathtub that are not being reglazed.
Bathtub Priming: We will apply a primer to the surface of the bathtub to help the new surface coating adhere to the old surface.
Bathtub Surface Coating: We will apply a new surface coating to the bathtub. This coating may be applied with a spray gun or roller, depending on their preference. The surface coating is applied in several thin layers and is left to dry between each coating.
Bathtub Buffing: Once the surface coating has been applied, the reglazing company will buff the bathtub to smooth out any imperfections and create an even finish.
Final Bathtub Inspection: We will inspect the bathtub and make any necessary touch-ups or repairs.
